Have a question about a Digital Lightwave product? Need a quote? Click here to contact our sales professionals.
One box solution for lab, production line and remote network test / monitoring applications.
The NIC EP can be controlled remotely via the NIC remote control application or VNC or built into an automation system or remote monitoring system using the programmable SCPI interface.
Equip the NIC EP with the exact functionalities you need.
Maximise the testing you carry out by testing up to 48 ports at any time. Configure fully independent test scenarios and generate automatic test reports.
Minimize on-site footprint by installing up to 5 modules in a single chassis
Provide test resources to multiple technicians in a single unit.
Support for SDH, SONET, OTN, Ethernet, Fibre Channel, PDH, ATM, serial interface and DWDM testing capabilities.
Automatic report generation - just disconnect from the network and go without needing to generate reports on your PC.
Test tomorrows technologies as well as todays SONET/SDH, OTN, 40Gb/s, 43Gb/s, Ethernet, Fibre Channel and advanced NGN mappings.
The NIC platform is ready to support 100G/s for your 100G product and service introduction.
Ready for 100Gb/s
Today's transport networks feature a multitude of layers and mapped protocols. The NIC fully supports multi-layer service testing allowing you to test at OTN or SONET/SDH interfaces with support for GFP/GMP mapping of Ethernet, 10 Gigabit Ethernet and Fibre Channel services and analysis of any intermediate control layers.
Your test is only as valuable as the results it produces. The NIC provides in-depth reporting including full error and alarm counts and rate display, graphing capabilities, report generation, and full event logs recording the beginning and end of every single event that is detected, whether it be a single bit error or an hour long loss of frame, not one detail is missed ensuring you can pinpoint the cause of any network issues.
NGN networks require not only bit error rate testing of a circuit but analysis at each of the layers / protocols supporting the delivered service. Use the NIC to perform service testing including Ethernet stress testing, Fibre Channel throughput, QoS testing, RFC-2544 benchmarking from lower layer protocols and analyze the mapping mechanisms that are being used in the transport of that service.
Test 40 Gigabit SONET/SDH and OTN networks using OC-768 / STM-256 and OTU-3 interfaces.
Support layered data services and full ODU multiplex structures including Ethernet mapped from an ODU-0 through to the ODU-3 and Ethernet mapped through GFP into SONET/SDH.
SONET/SDH test features
OTN test features
The definition of flexibility the MSA 2020 / 2030 modules support 5 physical protocols on a single module. A single module is all that's needed to test Ethernet, Fibre Channel, SDH, SONET and OTN interfaces up to 10Gb/s rates.
Maximise the usage of the module by testing up to 3 separate interfaces simultaneously, mixing dual 1Gbs/s, 2Gb/s, 4Gb/s, 1000Base-T, Fast Ethernet and Gigabit Ethernet testing with 10G Ethernet LAN / WAN PHY, 8G, 10G Fibre Channel, SDH and OTN ports.
tester with this module to testSDH features
NGN SONET/SDH test features
OTN test features
Ethernet test features
Fibre Channel test features
Testing multiple Ethernet ports simultaneously can shorten overall test time, reduce your implementation time and save money. With the High Density Ethernet module for the NIC platform, you can test up to eight electrical ports and four optical ports on a single High Density Ethernet module. Up to four of these modules can be installed in the NIC Plus or NIC EP chassis enabling even higher density. Add 10GigE LAN/WAN testing to fully test Ethernet systems at today’s highest data-rates.
Up to 12 ports supporting 10 / 100 / 1000 Base-T, Fast Ethernet, Gigabit Ethernet and Fibre Channel at 1Gb/s and 2 Gb/s.
Ethernet test features
Fibre Channel test features
Cost effective module supporting legacy SONET/SDH and OTN testing.
SONET/SDH test features
OTN test features
Support your existing copper infrastructure with the PDH test module, supporting up to 4 interfaces from 1.5Mb/s to 140Mb/s.
PDH test features
Test support for low speed serial interfaces.
Serial interface test features
DWDM Optical Spectrum Analyser
DWDM test features
Please provide the following information:
Name *
Email *
Company *
Phone *
Country *
Title
Product Line
Technology
Subject
Message
Receive helpful tips and special offers from Digital Lightwave?
For DLI Tech Support issues, please provide the following information and a customer service representative will respond to your request as soon as possible.
Emails received after 5:30pm EST will be replied to the next business day.
Name *
Email *
Company *
Phone *
Country
Product
Serial Number
Software Version
Message
Receive helpful tips and special offers from Digital Lightwave?
